1、電動機—般安裝在室內清潔、干燥的場所，周圍必須通風良好，環境空氣最高溫度不超過40℃，最低溫度不低于-15℃，并應防止強烈的熱輻射。  
2、按接線圖接電源線接線頭連接要緊固，帶引出電纜、電線的電動機，可直接和電源線連接，接頭處要絕緣密封。 
3、當電源線，相序和電動粗接線頭標志對應連接時，從軸伸端看電動機順時針旋轉。需要改變轉向時，改變兩根電源線接線的位置即可。 
4、YD系列等變級多速異步電動機是利用換接引出線的方法來控制轉速變化的，為保證多速電動機運行的可靠性，設計和操作控制裝置時應注意，在高速切換為低速時，必須在切斷電源的同時斷開2Y接線的中性點，以免在低速繞組接通時引起電源短路．在高速切換為低速的過程中，必續待電動機停轉后才能接通低速繞組的電源，以減少對電動機及負載的沖擊．轉速切換要注意電動機的轉向。 
5、電動機可以采有聯軸器，齒輪、皮帶與負載機械聯接，4kw以上的2極電動機30kw以上的4極電動機不宜用皮帶傳動，雙軸伸電動的第二軸伸只能用聯軸囂傳動。聯軸器、皮帶輪軸孔與電動機軸的配合松緊應合適，安裝時嚴禁用重錘敲擊。采用聯軸器傳動時，電動機軸中心線與負載機械軸中心線應重合， 
聯軸器軸向保留1～3mm間隙。 采用皮帶傳達室動時，電動機軸中心線應與負載機械軸中心線平行，皮帶中心線與軸中心線相互垂直。